Enter your motorcycle make and model to learn more about how to install a Scottoiler chain oiler system on your bike:

Tiger 955 (2001 - 2003)

 

 Product Compatibility

  • vSystem + Adapters SA-0155BL & SA-0176BL
  • Sport Edition vSystem + Adapters SA-0155BL & SA-0176BL
  • xSystem
  • eSystem + Adapter SA-0176BL
  • Lube Tube
  • Dual Injector
  • Scorpion Dual Injector
  • Magnum HCR

 
 
Please Note

The HCR (High Capacity Reservoir) is not compatible with this model. If you are looking to increase the reservoir capacity we recommend the Lube Tube flexible reservoir instead.

 

  1. Go to vSystem Installation
  2. Go to eSystem Installation
  3. Go to Comments and Feedback

 

vSystem Installation

 
 
Adapter Required!

This installation requires a Triumph Tee connector with Viton (SA-0155BL) , available from Scottoiler,

 

 
Adapter Required

 This installation requires an adapter for eccentric cam chain models (SA-0176BL) to secure the dispenser on the swing arm.

 

 

Step 1 - Find a vacuum source 

 

 

Locate the vacuum – There three corrugated vacuum pipes from spigots on the throttle bodies to the "stepper motor". Choose the longest and cut into this pipe and insert the cut ends all the way into either end of the Viton tubing on each side of the tee connector (SA-0155BL), available  from Scottoiler. Then press the Damper Elbow onto the third (middle) leg of the tee. For further information see our easy step installation guide - Vacuum Connections, General.

 

 

 

 

Step 2 - Find a place for the reservoir 

 

The reservoir can be mounted on the frame or under the seat. The more vertical the reservoir is mounted the better. Avoid positioning the reservoir completely horizontally, as this will limit the available range. Remember to avoid exhaust and engine components. For further information, see our easy step installation guide – Reservoir Positions.

 

 

 

 

Step 3 - Mount the dispenser and connect the system

 

The dispenser plate is secured to the swing arm using the small dispenser plate and the Dispenser Adapter (SA-0176BL) - for eccentric chain adjuster models, available from Scottoiler. The tip of the Injector should lightly touch the sprocket face with the slash cut facing outwards.

 

 

 

Step 4 - Fill, prime and set up your vSystem

Once fitted, fill and prime the system and set the adjuster knob to ’prime’. Start the engine and turn the adjuster knob until a flow of between 1 and 2 drops per minute is achieved. Check the condition of your chain after a ride, and then adjust as required.  

For best results clean your chain before fitting the Scottoiler using paraffin or similar. Then lightly oil the chain from the bottle using a rag or a brush, this allows the oil from the Scottoiler to reach both sides of the chain. 1 to 2 drops per minute will maintain this film of oil on the chain.

 

 


 

eSystem Installation

 
Adapter Required

 This installation requires an adapter for eccentric cam chain models (SA-0176BL) to secure the dispenser on the swing arm.

 

Step 1 - Find a place for the display

The Display Bracket (Part 5) can be rotated through 360° to give 4 mounting options and can also be flipped to provide 4 further options. The bracket can be secured to any M5/M6 bolt e.g. brake or clutch lever, brake cylinder or fairing mountings, in some cases you might need to trim the supplied bolt. It is possible to bend the bracket to shape, do so before fitting the Display Unit, part 1, to prevent damage to the unit. Alternatively, the sticky fasteners (Part 4) can be used to securely fasten the Display Unit to any flat surface e.g. the fork yokes.

 

Step 2 - Find a space for the reservoir

 

The reservoir can be mounted on the frame or under the seat. The more vertical the reservoir is mounted the better. Avoid positioning the reservoir completely horizontally, as this will limit the available range. Remember to avoid exhaust and engine components. For further information, see our easy step installation guide – Reservoir Positions.

 

 Note: vSystem reservoir shown
 

Step 3 - Mount dispenser on your rear sprocket

 

The dispenser plate is secured to the swing arm using the small dispenser plate and the Dispenser Adapter (SA-0176BL) - for eccentric chain adjuster models, available from Scottoiler. The tip of the Injector should lightly touch the sprocket face with the slash cut facing outwards.

 

 
 

 

Step 4 - Connect system to your battery

The eSystem must be wired directly to the battery. Attach the red wire to the +ve terminal and attach the black wire to the -ve terminal.

If you want to learn more about the eSystem Battery Connection and Power Consumption please click here

Step 5 - Fill, prime, and set up your new eSystem

Once fitted, fill the REP and prime the pump. Attach the delivery tubing and prime until the oil reaches the rear sprocket and then install the check valve. Do not install the check valve until the delivery tubing is full.

For further information you can also watch our installation video that shows the setup steps. How to fill and prime my eSystem?

Set the flow rate, using the ’Driving Screen’ on the Display Unit, to 60-70 seconds per drop (s/dp), check the condition of your chain after a ride, and adjust as required.


 

Your Comments and Feedback

We would love to hear about your experience. Maybe you have found a better way to install the Scottoiler? A neater way to route the tubing or hide the reservoir? Maybe you even have a better picture of your installation? Our model-specific installation guides live off your tips, ideas and photos. Help us to help all motorcyclists. E-mail us at technical@scottoiler.com

Attachments
There are no attachments for this article.