Enter your motorcycle make and model to learn more about how to install a Scottoiler chain oiler system on your bike:

MT-09 + FZ-09 - (2014 >)

MT09 proffiile

 Product Compatibility

  • vSystem
  • Sport Edition vSystem
  • eSystem
  • Lube Tube
  • Dual Injector
  • Magnum HCR

 

 

Please Note

The Dual Injector accessory is not compatible with this model. We recommend the standard single injector assembly instead. Read more about Dispenser Positioning

 
Please Note

The HCR (High Capacity Reservoir) is not compatible with this model. If you are looking to increase the reservoir capacity we recommend the Lube Tube flexible reservoir instead.

  

 

  1. Go to vSystem Installation
  2. Go to eSystem Installation
  3. Go to Comments and Feedback

 

vSystem Installation

Step 1 - Find a vacuum source 

Locate the vacuum – There is a rubber cap over a spigot on the inlet tract.  Remove this cap and then press the Damper Elbow, onto the spigot. For further information see our easy step installation guide - Vacuum Connections General.

MT09 FZ90 (2014 - ) rubber cap on throttle body There are rubber caps on each throttle body.

 

 
 

MT09 FZ09 (2014 - ) damper elbow on spigot Remove the rubber cap and replace it with the vacuum damper elbow part.

Hint: fit the vacuum tubing to the small end of the vacuum damper elbow first.

 

Step 2 - Find a place for the reservoir 

The reservoir can be mounted on the frame or under the seat. The more vertical the reservoir is mounted the better. Avoid positioning the reservoir completely horizontally, as this will limit the available range. Remember to avoid exhaust and engine components. For further information, see our easy step installation guide – Reservoir Positions.

MT09 FZ09 reservoir under seat .

 

Step 3 - Mount the dispenser and connect the system 

The Dispenser Assembly can be secured to the paddock stand bobbin mount using the small Dispenser Plate & Clip. The delivery tubing can be routed along the swing arm using self- adhesive cable clips. For further information see our easy step installation guide - Dispenser Positioning. The nib should feed the rear sprocket with the cut face facing outwards.

MT09  FZ09 dispenser on bobbin.

 

Step 4 - Fill, prime and set up your vSystem

Once fitted, fill and prime the system and set the adjuster knob to ’prime’. Start the engine and turn the adjuster knob until a flow of between 1 and 2 drops per minute is achieved. Check the condition of your chain after a ride, and then adjust as required.  

For best results clean your chain before fitting the Scottoiler using paraffin or similar. Then lightly oil the chain from the bottle using a rag or a brush, this allows the oil from the Scottoiler to reach both sides of the chain. 1 to 2 drops per minute will maintain this film of oil on the chain.

 

 


 

eSystem Installation

Step 1 - Find a place for the display

The Display Bracket (Part 5) can be rotated through 360° to give 4 mounting options and can also be flipped to provide 4 further options. The bracket can be secured to any M5/M6 bolt e.g. brake or clutch lever, brake cylinder or fairing mountings, in some cases you might need to trim the supplied bolt. It is possible to bend the bracket to shape, do so before fitting the Display Unit, part 1, to prevent damage to the unit. Alternatively, the sticky fasteners (Part 4) can be used to securely fasten the Display Unit to any flat surface e.g. the fork yokes.

eSystem display - genericThe display can be mounted at the handlebars.  Please note: this is a generic image.

 

Step 2 - Find a space for the reservoir

The reservoir can be mounted under the seat or on a frame spar. Ensure that the top of the reservoir is at least slightly raised to maximise the available range.

MT09 FZ09 RMV location The REP can be mounted under the seat. Please note: whilst this image shows the RMV, the REP can be mounted in the same place.

  

Step 3 - Mount dispenser on your rear sprocket

Make sure that the injector lightly touches the face of the sprocket. Use spindle mounts, bobbin mounts or chain guards to install the dispenser assembly. 

After you are happy with the placement of both the reservoir and the dispenser secure all parts before starting with the routing of the oil delivery tube. Take your time to find the best and most secure routing, avoiding hot engine and exhaust parts and taking suspension movement into account.  

MT09 FZ09 dispenser on bobbin

.

 

Step 4 - Connect system to your battery

The eSystem must be wired directly to the battery. Attach the red wire to the +ve terminal and attach the black wire to the -ve terminal.

If you want to learn more about the eSystem Battery Connection and Power Consumption please click here

Step 5 - Fill, prime, and set up your new eSystem

Once fitted, fill the REP and prime the pump. Attach the delivery tubing and prime until the oil reaches the rear sprocket and then install the check valve. Do not install the check valve until the delivery tubing is full.

For further information you can also watch our installation video that shows the setup steps. How to fill and prime my eSystem?

Set the flow rate, using the ’Driving Screen’ on the Display Unit, to 60-70 seconds per drop (s/dp), check the condition of your chain after a ride, and adjust as required.


 

Your Comments and Feedback

We would love to hear about your experience. Maybe you have found a better way to install the Scottoiler? A neater way to route the tubing or hide the reservoir? Maybe you even have a better picture of your installation? Our model-specific installation guides live off your tips, ideas and photos. Help us to help all motorcyclists.

Attachments
There are no attachments for this article.